- Characteristics
- Instructions
- Applications
- Certificates
Technical specifications
The DOMOLAM metal sheets for roofing and cladding are produced according to the standards EN 14782:2006. The results shown on the resistance tables have been arosen from finite element analysis and experimental verification. Calculations were made with reference to the real thickness, which is lower than the nominal one by the coating thickness (0,04mm for 275gr/m2).
• Seating width b ≥ 50mm.
• Acceptable deflection F ≤ ℓ / 200, E= 2,1 x 106 kg/cm2, uniformly distributed load (Kp/m2).
• Safety factor = 2.
• Yield strength fvb = 280 N/mm2.
The material weight has been subtracted from the loads.
Specification of raw materials
Raw materials complying with high quality and technical standards are used as:
• Pre-painted galvanized coils: According to the standard EN 10169:2010 + Α1:2012 with standard polyester 25μ paint in 30 colors.
• Silicon polyester paints, PVDF and other colors upon request.
The DOMOLAM metal sheets for roofing and cladding are produced according to the standards EN 14782:2006. The results shown on the resistance tables have been arosen from finite element analysis and experimental verification. Calculations were made with reference to the real thickness, which is lower than the nominal one by the coating thickness (0,04mm for 275gr/m2).
• Seating width b ≥ 50mm.
• Acceptable deflection F ≤ ℓ / 200, E= 2,1 x 106 kg/cm2, uniformly distributed load (Kp/m2).
• Safety factor = 2.
• Yield strength fvb = 280 N/mm2.
The material weight has been subtracted from the loads.
Specification of raw materials
Raw materials complying with high quality and technical standards are used as:
• Pre-painted galvanized coils: According to the standard EN 10169:2010 + Α1:2012 with standard polyester 25μ paint in 30 colors.
• Silicon polyester paints, PVDF and other colors upon request.
Transportation
Long packs should be unloaded either with the use of spreader beam or long belts.
Storage
Should be tilted and covered in such a way as to ensure ventilation, in order to avoid vapor condensation and electrochemical corrosion.
Pre-painted sheets should not be dragged.
After the installation, the protective film (if any) should be removed and the roof should be cleaned from cutting and drilling swarfs.
Pre-painted sheets should not be dragged.
After the installation, the protective film (if any) should be removed and the roof should be cleaned from cutting and drilling swarfs.
Installation
It is recommended that the purlins are placed tile by tile in order to ensure the sufficient support of the sheet. The screws are placed alternatively at the points shown at the figure.
During fitting, highly concentrated loads between the purlins should be avoided.
It is recommended that at least 2 fasteners should be used on each sheet and purlin, except for the top and bottom part of the sheet, where 3 are necessary.
Fastening should stop when the sheet starts deforming under the screw, to ensure the best aesthetic and static results.
It is recommended that the purlins are placed tile by tile in order to ensure the sufficient support of the sheet. The screws are placed alternatively at the points shown at the figure.
During fitting, highly concentrated loads between the purlins should be avoided.
It is recommended that at least 2 fasteners should be used on each sheet and purlin, except for the top and bottom part of the sheet, where 3 are necessary.
Fastening should stop when the sheet starts deforming under the screw, to ensure the best aesthetic and static results.
| external plate | width | length | packaging | quantity | Price | ||||||||||||||
| code | material | thickness | operating | spread | unit | length (mm) | small | big | weight (kg/m) | weight (kg/m2) | quantity | price per unit (€) | value (€) | Comments | |||||
| Successfully added to cart Quantity is missing Length is missing | TLF 23/183 TLF 23/183 | French tiles | Τα χρώματα στις φωτογραφίες των έργων είναι ενδεικτικά και μπορεί να διαφέρουν από την πραγματικότητα, εξαιτίας των ρυθμίσεων της οθόνης, των συνθηκών φωτισμού και του περιβάλλοντος χώρου."> Τα χρώματα στις φωτογραφίες των έργων είναι ενδεικτικά και μπορεί να διαφέρουν από την πραγματικότητα, εξαιτίας των ρυθμίσεων της οθόνης, των συνθηκών φωτισμού και του περιβάλλοντος χώρου."> RAL 3003 RAL 6005 | NO_FILM | 1010 | 1250 | kg | 1 | 0.98 | ||||||||||
You might also need these products
French tiles TLF 23/183
The “French” tiles DOMOLAM offer a low cost solution for simple constructions of low demands. With a static height of 23mm they demand for a 35cm purlin distance and they are ideal for roofs with a minimum inclination of 6% and short length.
The DOMOLAM metal sheets for roofing and cladding are produced by the continuous cold roll forming process and already include seven different profiles, to fully satisfy all needs, such as the covering of industrial and manufacturing buildings, warehouses and sheds, agricultural and animal breeding facilities, airport and military buildings, sports and shopping centers, garages, etc.
Competitive advantages:
• The wide range of products offers a choice among numerous widths andt hicknesses in order to achieve the most resistant, cost-efficient and aesthetical constructions.
• The option of using wide sheets considerably reduces the overall cost for customers, in terms of material purchase cost (-3%), fastening materials (-10%), and labor cost (-15%).
• Prompt delivery of any desirable dimension and quantity.
The DOMOLAM metal sheets for roofing and cladding are produced by the continuous cold roll forming process and already include seven different profiles, to fully satisfy all needs, such as the covering of industrial and manufacturing buildings, warehouses and sheds, agricultural and animal breeding facilities, airport and military buildings, sports and shopping centers, garages, etc.
Competitive advantages:
• The wide range of products offers a choice among numerous widths andt hicknesses in order to achieve the most resistant, cost-efficient and aesthetical constructions.
• The option of using wide sheets considerably reduces the overall cost for customers, in terms of material purchase cost (-3%), fastening materials (-10%), and labor cost (-15%).
• Prompt delivery of any desirable dimension and quantity.
